Just How to Set up a Bathtub Yourself
Just How to Set up a Bathtub Yourself
Blog Article
This post following next on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is truly captivating. Give it a try and make your own personal conclusions.
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old tub is conveniently obtainable, the job can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the new tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have certified on your own for the work and are comfortable attempting it. Instead of working with a service provider to take control of a halfway-completed project, it is better to think about employing one before you start. Possibilities are you might require a specialist plumber to make tube connections.
This article will assist you set up a brand-new tub in your shower room if you have actually currently acquired a brand-new bathtub and do not require to alter the plan of your previous supply of water pipes.
Your tools and product list must make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the tub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the tub must wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its last position.
Preparing for the Installment
To start with, the sustaining frame supplied with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to split an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, resulting in issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our piece about How to Install a Bathtub. Thank you for taking time to read through our article post. Are you aware of somebody else who is excited by the topic? Do not hesitate to share it. We love reading our article about Installing A Bathtub.
Schedule Now!
Report this page